AED
AFN
ALL
AMD
ANG
AOA
ARS
AUD
AWG
AZN
BAM
BBD
BDT
BGN
BHD
BIF
BMD
BND
BOB
BRL
BSD
BTN
BWP
BYN
BZD
CAD
CDF
CHF
CLF
CLP
CNH
CNY
COP
CRC
CUC
CUP
CVE
CZK
DJF
DKK
DOP
DZD
EGP
ERN
ETB
EUR
FJD
FKP
GEL
GGP
GHS
GIP
GMD
GNF
GTQ
GYD
HKD
HNL
HRK
HTG
HUF
IDR
ILS
IMP
INR
IQD
IRR
ISK
JEP
JMD
JOD
JPY
KES
KGS
KHR
KMF
KPW
KRW
KWD
KYD
KZT
LAK
LBP
LKR
LRD
LSL
LYD
MAD
MDL
MGA
MKD
MMK
MNT
MOP
MRU
MUR
MVR
MWK
MXN
MYR
MZN
NAD
NGN
NIO
NOK
NPR
NZD
OMR
PAB
PEN
PGK
PHP
PKR
PLN
PYG
QAR
RON
RSD
RUB
RWF
SAR
SBD
SCR
SDG
SEK
SGD
SHP
SLE
SLL
SOS
SRD
SSP
STD
STN
SVC
SYP
SZL
THB
TJS
TMT
TND
TOP
TRY
TTD
TWD
TZS
UAH
UGX
USD
UYU
UZS
VES
VND
VUV
WST
XAF
XCD
XCG
XOF
XPF
YER
ZAR
ZMW
ZWG
ZWL
TANOL 200ml
Staining developer
High resolution
Maximum sharpness
Fine grain
Suitable for tank and dish development
It is also possible to use this developer in a rotation tank. However, in direct comparison the sharpness is significantly lower. If you want to use a developing machine, we recommend the TAS film processor by Heiland Electronic.
You do not need to rinse before developing the film. The only exception is Delta 400. After a couple of minutes of developing this film you get a lot of foam in the tank. If the tank is only filled to just about cover the film, this can lead to errors in development. You can overcome this problem by rinsing the film for 2 to 3 minutes before you develop.
Dilute developer and alkali with water in a ratio of 1+1+100. Do this immediately before you start developing. In such high dilutions the water quality can have consequences for the film speed. Therefore we recommend the use of distilled water. In tap water the film speed can be 1°DIN higher as well as lower than shown in the development table.
Unlike the familiar staining developers on the basis of pyrogallol, auto-oxidisation of Tanol starts a lot later. This is an advantage when developing N+ based on the zone system. During long development times you dont need to worry about early exhaustion.
As with pyrogallol a dye builds up proportionally to the silver density. The Tanol stain is less obvious to see than the pyro stain but just as effective. The dye accumulates between the grains of silver and lessens the impression of graininess that necessarily occurs with all sharpness developers.
When using graded paper the stain has little influence on the highlight contrast as long as you stick with the recommended times. On VC paper the stain acts as an additional soft filter in the higher densities.
This developer is especially interesting for large format negatives. The results will be suitable for conventional development as well as alternative development techniques such as platinotype and cyanotype. When using contact printing techniques of the early days of photography, you need negatives with dense highlights and a straight lined density curve. The contrast range should be between 1.7 and 2.0 logD. When printing, expose with daylight or UV light. Since the stain blocks UV light, you can print straight from the original negative.
The stock solutions have a shelf life of 2 to 3 years (even when opened)
Included in delivery of Tanol:
2x100ml for the preparation of 10 litres of working solution – capacity 40 films
High resolution
Maximum sharpness
Fine grain
Suitable for tank and dish development
It is also possible to use this developer in a rotation tank. However, in direct comparison the sharpness is significantly lower. If you want to use a developing machine, we recommend the TAS film processor by Heiland Electronic.
You do not need to rinse before developing the film. The only exception is Delta 400. After a couple of minutes of developing this film you get a lot of foam in the tank. If the tank is only filled to just about cover the film, this can lead to errors in development. You can overcome this problem by rinsing the film for 2 to 3 minutes before you develop.
Dilute developer and alkali with water in a ratio of 1+1+100. Do this immediately before you start developing. In such high dilutions the water quality can have consequences for the film speed. Therefore we recommend the use of distilled water. In tap water the film speed can be 1°DIN higher as well as lower than shown in the development table.
Unlike the familiar staining developers on the basis of pyrogallol, auto-oxidisation of Tanol starts a lot later. This is an advantage when developing N+ based on the zone system. During long development times you dont need to worry about early exhaustion.
As with pyrogallol a dye builds up proportionally to the silver density. The Tanol stain is less obvious to see than the pyro stain but just as effective. The dye accumulates between the grains of silver and lessens the impression of graininess that necessarily occurs with all sharpness developers.
When using graded paper the stain has little influence on the highlight contrast as long as you stick with the recommended times. On VC paper the stain acts as an additional soft filter in the higher densities.
This developer is especially interesting for large format negatives. The results will be suitable for conventional development as well as alternative development techniques such as platinotype and cyanotype. When using contact printing techniques of the early days of photography, you need negatives with dense highlights and a straight lined density curve. The contrast range should be between 1.7 and 2.0 logD. When printing, expose with daylight or UV light. Since the stain blocks UV light, you can print straight from the original negative.
The stock solutions have a shelf life of 2 to 3 years (even when opened)
Included in delivery of Tanol:
2x100ml for the preparation of 10 litres of working solution – capacity 40 films
Product Condition:
New
Updating Order Details
Please do not refresh or navigate away from the page!
No Reviews Posted Yet - be the first! (write review)
